Same tapered threads as the standard innerduct pulling eye, these pulling eyes feature a slotted head with clevis pin to permit direct attachment to any multiple pulling harness leg ends. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.

NOTE: To determine correct pulling eye size, obtain the actual innerduct inside diameter (I.D.). The I.D. measurement must be greater than dimension A and smaller than dimension B.
1 - 13 of 13 | Results Per Page | View | Unit of Measure
1 

Part #

Nom. Size (in.)

Nom. Size (mm)

Innerduct I.D. Range A to B (in.)

Innerduct I.D. Range A to B (mm)

Max. O.D. C (in.)

Max. O.D. C (mm)

Add to Quote
08913500 N/A 3/4 N/A 19 N/A 0.68 to 0.81 N/A 17 to 21 N/A 1.13 N/A 29 Add to Quote
08913501 N/A 7/8 N/A 22 N/A 0.81 to 0.93 N/A 21 to 24 N/A 1.25 N/A 32 Add to Quote
08913502 N/A 1 N/A 25 N/A 0.93 to 1.06 N/A 24 to 27 N/A 1.38 N/A 35 Add to Quote
08913340 N/A 1 N/A 25 N/A 0.98 to 1.14 N/A 25 to 29 N/A 1.38 N/A 35 Add to Quote
08913503 N/A 1-1/4 N/A 32 N/A 1.06 to 1.18 N/A 27 to 30 N/A 1.44 N/A 37 Add to Quote
08913504 N/A 1-1/4 N/A 32 N/A 1.18 to 1.34 N/A 30 to 34 N/A 1.63 N/A 41 Add to Quote
08913341 N/A 1-1/4 N/A 32 N/A 1.23 to 1.39 N/A 31 to 35 N/A 1.63 N/A 41 Add to Quote
08913505 N/A 1-1/2 N/A 38 N/A 1.34 to 1.50 N/A 34 to 38 N/A 1.88 N/A 48 Add to Quote
08913506 N/A 1-1/2 N/A 38 N/A 1.50 to 1.62 N/A 38 to 41 N/A 2.00 N/A 51 Add to Quote
08913507 N/A 1-1/2 N/A 44 N/A 1.68 to 1.81 N/A 43 to 46 N/A 2.00 N/A 51 Add to Quote
08913510 N/A 2 N/A 51 N/A 1.82 to 1.96 N/A 46 to 50 N/A 2.50 N/A 64 Add to Quote
08913508 N/A 2 N/A 51 N/A 1.96 to 2.09 N/A 50 to 53 N/A 2.50 N/A 64 Add to Quote
08913509 N/A 2 N/A 51 N/A 2.06 to 2.18 N/A 52 to 56 N/A 2.50 N/A 64 Add to Quote
1 - 13 of 13 | Results Per Page | View | Unit of Measure
1