Colonial TelTek
Colonial TelTek
201 W. Church Road
King of Prussia, PA 19406
Phone: (855) 686-7713
Email: Info@colonialteltek.com
Website: www.knobsource.com
Print Back
Same tapered threads as the standard innerduct pulling eye, these pulling eyes feature a slotted head with clevis pin to permit direct attachment to any multiple pulling harness leg ends. When properly sized and installed, these eyes will not pull out of the innerduct until the pulling tensions have greatly exceeded the maximum pulling tensions recommended by the innerduct manufacturers.

NOTE: To determine correct pulling eye size, obtain the actual innerduct inside diameter (I.D.). The I.D. measurement must be greater than dimension A and smaller than dimension B.
Clevis Head Innerduct Pulling Eyes
Clevis Head Innerduct Pulling Eyes-2
Unit of Measure
Items Clevis Head Innerduct Pulling Eyes
08913500
Clevis Head Innerduct Pulling Eyes 		Clevis Head Innerduct Pulling Eyes
08913501
Clevis Head Innerduct Pulling Eyes 		Clevis Head Innerduct Pulling Eyes
08913502
Clevis Head Innerduct Pulling Eyes 		Clevis Head Innerduct Pulling Eyes
08913340
Clevis Head Innerduct Pulling Eyes 		Clevis Head Innerduct Pulling Eyes
08913503
Clevis Head Innerduct Pulling Eyes
Nom. Size (in.) N/A 3/4 N/A 7/8 N/A 1 N/A 1 N/A 1-1/4
Nom. Size (mm) N/A 19 N/A 22 N/A 25 N/A 25 N/A 32
Innerduct I.D. Range A to B (in.) N/A 0.68 to 0.81 N/A 0.81 to 0.93 N/A 0.93 to 1.06 N/A 0.98 to 1.14 N/A 1.06 to 1.18
Innerduct I.D. Range A to B (mm) N/A 17 to 21 N/A 21 to 24 N/A 24 to 27 N/A 25 to 29 N/A 27 to 30
Max. O.D. C (in.) N/A 1.13 N/A 1.25 N/A 1.38 N/A 1.38 N/A 1.44
Max. O.D. C (mm) N/A 29 N/A 32 N/A 35 N/A 35 N/A 37
Hole Diameter D (in.) N/A 0.25 N/A 0.25 N/A 0.38 N/A 0.38 N/A 0.38
Hole Diameter D (mm) N/A 6 N/A 6 N/A 10 N/A 10 N/A 10
Slot Width E (in.) N/A 0.38 N/A 0.56 N/A 0.56 N/A 0.56 N/A 0.59
Slot Width E (mm) N/A 10 N/A 14 N/A 14 N/A 14 N/A 15
Slot Depth F (in.) N/A 1.06 N/A 1.34 N/A 1.31 N/A 1.31 N/A 1.41
Slot Depth F (mm) N/A 27 N/A 34 N/A 33 N/A 33 N/A 36
Pin Diameter G (in.) N/A 0.31 N/A 0.38 N/A 0.44 N/A 0.44 N/A 0.44
Pin Diameter G (mm) N/A 8 N/A 10 N/A 11 N/A 11 N/A 11
Pin Center H (in.) N/A 0.53 N/A 0.59 N/A 0.56 N/A 0.56 N/A 0.59
Pin Center H (mm) N/A 13 N/A 15 N/A 14 N/A 14 N/A 15
Note N/A Will fit the 1/8" and 1/4" cable pulling harnesses only. N/A Will fit all Condux multiple pulling harnesses. N/A Will fit all Condux multiple pulling harnesses. N/A Will fit all Condux multiple pulling harnesses. N/A Will fit all Condux multiple pulling harnesses.